Gandalf/OctoPrint-Enclosure
1
0
Fork 0
Code Issues 156 Pull Requests 6 Actions Packages Projects Releases 28 Wiki Activity

Add markdown formatting

Browse Source
This commit is contained in:
coliss86
2020-12-23 15:12:10 +01:00
committed by GitHub
parent db22b12d83
commit d7416837f6
1 changed files with 66 additions and 42 deletions
Download Patch File Download Diff File Expand all files Collapse all files

108
README.md
View File

@@ -28,13 +28,21 @@ Here is a list of possibilities:
Check pictures on thingiverse: http://www.thingiverse.com/thing:2245493
**Software**
## Software
### Installation
Install the plugin using the Plugin Manager bundled with OctoPrint, you can search for the Enclosure plugin or just use the url: https://github.com/vitormhenrique/OctoPrint-Enclosure/archive/master.zip.
## Hardware
This plugin support many hardware temperature sensors and led controller. Here are detailled instructions on how to setup them
### Temperature sensor
To control the enclosure temperature or get temperature triggered events, you need to install and configure a temperature sensor. This plugin can support DHT11, DHT22, AM2302, DS18B20, SI7021, BME280 and TMP102 temperature sensors.
* For the DHT11, DHT22 and AM2302 follow this steps:
#### DHT11, DHT22 and AM2302 sensors
Wire the sensor following the wiring diagram on the pictures on thingiverse, you can use any GPIO pin.
@@ -42,72 +50,89 @@ For DHT11 and DHT22 sensors, don't forget to connect a 4.7K - 10K resistor from
You need to install Adafruit library to use the temperature sensor on raspberry pi.
Open raspberry pi terminal and type:
Open a raspberry pi terminal and type:
<pre><code>cd ~
```
cd ~
git clone https://github.com/adafruit/Adafruit_Python_DHT.git
cd Adafruit_Python_DHT
sudo apt-get update
sudo apt-get install build-essential python-dev python-openssl
sudo python setup.py install</code></pre>
sudo python setup.py install
```
Note: All libraries need to be installed on raspberry pi system python not octoprint virtual environment.
You can test the library by using:
<pre><code>cd examples
```
cd examples
sudo ./AdafruitDHT.py 2302 4</code></pre>
```
Note that the first argument is the temperature sensor (11, 22, or 2302), and the second argument is the GPIO that the sensor was connected.
* For the DS18B20 sensor:
#### DS18B20 sensor
Follow the wiring diagram on the pictures on thingiverse. The DS18B20 uses "1-wire" communication protocol, you need to use 4.7K to 10K resistor from the data pin to VCC, DS18B20 only works on GPIO pin number 4 by default. You also need to add OneWire support for your raspberry pi.
Start by adding the following line to /boot/config.txt
Start by adding the following line to `/boot/config.txt`
<pre><code>dtoverlay=w1-gpio</code></pre>
```
dtoverlay=w1-gpio
```
After rebooting, you can check if the OneWire device was found properly with
<pre><code>dmesg | grep w1-gpio</code></pre>
```
dmesg | grep w1-gpio
```
You should see something like
<pre><code>[ 3.030368] w1-gpio onewire@0: gpio pin 4, external pullup pin -1, parasitic power 0</code></pre>
```
[ 3.030368] w1-gpio onewire@0: gpio pin 4, external pullup pin -1, parasitic power 0
```
You should be able to test your sensor by rebooting your system with sudo reboot. When the Pi is back up and you're logged in again, type the commands you see below into a terminal window. When you are in the 'devices' directory, the directory starting '28-' may have a different name, so cd to the name of whatever directory is there.
You should be able to test your sensor by rebooting your system with `sudo reboot`. When the Pi is back up and you're logged in again, type the commands you see below into a terminal window. When you are in the 'devices' directory, the directory starting '28-' may have a different name, so `cd` to the name of whatever directory is there.
<pre><code>sudo modprobe w1-gpio
```
sudo modprobe w1-gpio
sudo modprobe w1-therm
cd /sys/bus/w1/devices
ls
cd 28-xxxx (change this to match what serial number pops up)
cat w1_slave</code></pre>
cat w1_slave
```
The response will either have YES or NO at the end of the first line. If it is yes, then the temperature will be at the end of the second line, in 1/000 degrees C.
The response will either have `YES` or `NO` at the end of the first line. If it is `YES`, then the temperature will be at the end of the second line, in 1/000 degrees C.
Copy the serial number, you will need to configure the plugin. Note that for the serial number includes the 28-, for example 28-0000069834ff.
Copy the serial number, you will need to configure the plugin. Note that for the serial number includes the `28-`, for example `28-0000069834ff`.
* For the SI7021, BME280, TMP102 and MCP9808 sensors
#### SI7021, BME280, TMP102 and MCP9808 sensors
Enable I2C on your raspberry pi, depending on raspi-config version, step by step can be different:
<pre><code>Run sudo raspi-config
Use the down arrow to select 9 Advanced Options
Arrow down to A7 I2C
Select yes when it asks you to enable I2C
Also select yes when it asks about automatically loading the kernel module
Use the right arrow to select the button
Select yes when it asks to reboot
</code></pre>
```
sudo raspi-config
```
* Use the down arrow to select 9 Advanced Options
* Arrow down to A7 I2C
* Select yes when it asks you to enable I2C
* Also select yes when it asks about automatically loading the kernel module
* Use the right arrow to select the button
* Select yes when it asks to reboot
Install some packages (on raspberry pi system python not octoprint virtual environment):
<pre><code>sudo apt-get install i2c-tools python-pip python-smbus</code></pre>
```
sudo apt-get install i2c-tools python-pip python-smbus
```
Find the address of the sensor:
<pre><code>i2cdetect -y 1</code></pre>
```
i2cdetect -y 1
```
* For Neopixel
### For Neopixel
If your setup does not have pip install pip:
`sudo apt-get install python-pip`
@@ -125,22 +150,21 @@ Also backlist the audio kernel:
`sudo nano /etc/modprobe.d/snd-blacklist.conf`
add the `blacklist snd_bcm2835` to the end of the file:
add the `blacklist snd_bcm2835` to the end of the file.
* GPIO
This release uses RPi.GPIO to control IO of raspberry pi, it should install and work automatically. If it doesn't please update your octoprint with the latest release of octopi.
**Hardware**
### External hardware
You can use relays / mosfets to control you lights, heater, lockers etc... If you want to control mains voltage I recommend using PowerSwitch Tail II.
* Relay
#### Relay
The relays module that I used couple [SainSmart 2-Channel Relay Module](https://www.amazon.com/gp/product/B0057OC6D8?ie=UTF8&tag=3dpstuff-20&camp=1789&linkCode=xm2&creativeASIN=B0057OC6D8). Those relays are active low, that means that they will turn on when you put LOW on the output of your pin. In order to not fry your Raspberry Pi pay attention on your wiring connection: remove the jumper link and connect 3.3v to VCC, 5V to JD-VCC and Ground to GND.
* Heater
#### Heater
For heating my enclosure I got a $15 lasko inside my enclosure. I opened it and added a relay to the mains wire. If you’re uncomfortable soldering or dealing with high voltage, please check out the [PowerSwitch Tail II](http://www.powerswitchtail.com/) . The PowerSwitch Tail II is fully enclosed, making it a lot safer.
@@ -148,11 +172,11 @@ For heating my enclosure I got a $15 lasko inside my enclosure. I opened it and
**CAUTION 2: THIS HEATER IS NOT INTENDED TO FUNCTION THIS WAY AND IT MIGHT BE A FIRE HAZARD. DO IT AT YOUR OWN RISK**
* Cooler
#### Cooler
You can get a [USB Mini Desktop Fan](https://www.amazon.com/gp/product/B00WM7TRTY?ie=UTF8&tag=3dpstuff-20&camp=1789&linkCode=xm2&creativeASIN=B00WM7TRTY) and control it over a relay.
* Filament sensor
#### Filament sensor
You have the ability to add a filament sensor to the enclosure, it will automatically pause the print and run a gcode command to change the filament if you run out of filament, I can be any type of filament sensor, the sensor should connect to ground if is set as an "active low" when the filament run out or 3.3v if the sensor is set as "active high" when detected the end of filament, it does not matter if it is normally open or closed, that will only interfere on your wiring. I'm using the following sensor:
@@ -196,7 +220,7 @@ After selecting GPIO for the input type, and selecting output control on the act
Selecting print control on the action type will trigger printer actions when the configured GPIO receives a signal. The actions can be Resume and Pause a print job or Change Filament. You can use the "change filament" action and set up the input GPIO according to your filament sensor, for example, if your filament sensor connects to ground when detects the end of the filament, you should choose PULL UP resistors and detect the event on the falling edge.
You can also add mechanical buttons to pause, resume and change filaments near your printer for convenience.
**Advanced Area**
## Advanced Area
If you want to enable notifications check the following [issue](https://github.com/vitormhenrique/OctoPrint-Enclosure/issues/36)
@@ -204,16 +228,16 @@ You can control outputs using a simple [API](https://github.com/vitormhenrique/O
Or use [g-code](https://github.com/vitormhenrique/OctoPrint-Enclosure/wiki/G-CODE-Control) commands
**Tab Order**
### Tab Order
I often use more this plugin than the time-lapse tab, so having the plugin appear before the timelapse is better for me.
You can do this by changing the config.yaml file as instructed on [octoprint documentation ](http://docs.octoprint.org/en/master/configuration/config_yaml.html). Unless defined differently via the command line config.yaml is located at ~/.octoprint.
You can do this by changing the config.yaml file as instructed on [octoprint documentation ](http://docs.octoprint.org/en/master/configuration/config_yaml.html). Unless defined differently via the command line config.yaml is located at `~/.octoprint`.
You just need to add the following section:
<pre><code>appearance:
```
appearance:
components:
order:
tab:
@@ -222,4 +246,4 @@ You just need to add the following section:
- gcodeviewer
- terminal
- plugin_enclosure
</code></pre>
```